邢唷��>� tv��s{��欹�_ ��DAbjbjzyzy 1�6b6b(8��rrrrr��8�L ��'��(��F F F @'B'B'B'B'B'B'$�(�o+Xf'rF F F F F f'rr��H{'###F jr�r�d&�#F @'##8%t%��p�<�&鲈�� ^P%P&�'0�'l%�,!�,t%�,rt%�F F #F F F F F f'f'"�F F F �'F F F F ��,F F F F F F F F F �B8: SECTION 09 69 33 LOW PROFILE FIXED HEIGHT ACCESS FLOORING GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division�01 Specification Sections, apply to this Section. SUMMARY Section includes low-profile, fixed-height access flooring. COORDINATION Coordinate location of electrical work in underfloor cavity and wire management channels. PREINSTALLATION MEETINGS Retain "Preinstallation Conference" Paragraph below if Work of this Section is extensive or complex enough to justify a conference. Preinstallation Conference: Conduct conference at [Project site] . Review connections between low-profile, fixed-height access flooring and electrical systems. SUBMITTALS Product Data: For each type of product. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for low-profile, fixed-height access flooring. Include loading capacities. Shop Drawings: For low-profile, fixed-height access flooring: Include layout of low-profile, fixed-height access flooring and relationship to adjoining Work based on field-verified dimensions. Details and sections with descriptive notes indicating materials, finishes, fasteners, typical and special edge conditions, accessories, and understructures. Retain "Samples" Paragraph below, with a subordinate list if applicable. Samples: Exposed Metal Accessories: Approximately 10 inches (250 mm) in length. One full-size unit for each component of each type of low-profile, fixed-height access flooring required. Retain "Floor Coverings" Subparagraph for low-profile, fixed-height access flooring with factory-applied floor coverings; most manufacturers do not provide factory-applied finishes. Floor Coverings: Full-size units for each color and texture specified. Coordinate "Qualification Data" Paragraph below with qualification requirements in Section 014000 "Quality Requirements" and as may be supplemented in "Quality Assurance" Article. Qualification Data: For Installer. QUALITY ASSURANCE Installer Qualifications: An entity that employs installers and supervisors who are trained and approved by manufacturer. Mockups: Build mockups to verify selections made under Sample submittals, to demonstrate aesthetic effects, and to set quality standards for materials and execution. Build mockup of typical low-profile, fixed-height access flooring, as shown on Drawings. Size to be an area of no fewer than [five] floor panels in length by [five] floor panels in width. Approval of mockups does not constitute approval of deviations from the Contract Documents contained in mockups unless Architect specifically approves such deviations in writing. Retain subparagraph below if the intention is to make an exception to the default requirement in Section�014000 "Quality Requirements" for demolishing and removing mockups. Subject to compliance with requirements, approved mockups may become part of the completed Work if undisturbed at time of Substantial Completion. PRODUCTS Manufacturers and products listed in SpecAgent and Masterworks Paragraph Builder are neither recommended nor endorsed by the AIA or AVITRU. Before inserting names, verify that manufacturers and products listed there comply with requirements retained or revised in descriptions and are both available and suitable for the intended applications. For definitions of terms and requirements for Contractor's product selection, see Section�016000 "Product Requirements." PERFORMANCE REQUIREMENTS Retain "Seismic Performance" Paragraph below for projects requiring seismic design. Delete paragraph if performance requirements are indicated on Drawings. Model building codes and ASCE/SEI�7 establish criteria for buildings subject to earthquake motions. Coordinate requirements with structural engineer. Seismic Performance: Low-profile, fixed-height access flooring shall withstand the effects of earthquake motions determined according to [ASCE/SEI�7] . Loads in "Structural Performance" Paragraph below are examples only; revise to suit Project. If retained, verify that loading requirements coordinate with each other and match the products specified. If needed, revise the text. See the Evaluations. Structural Performance: Loading Capacity: [100-lbf/sq. ft. (4.8-kN/sq.爉)] [250-lbf/sq. ft. (12.0-kN/sq.爉)] live load with the following deflection and permanent set: Top-Surface Deflection: Maximum [0.15 inch (0.38 mm)] . Permanent Set: Maximum [0.06 inch (0.15 mm)] . Fire Performance: Surface-Burning Characteristics: Comply with ASTM燛84; testing by a qualified testing agency. Identify products with appropriate markings of applicable testing agency. Flame-Spread Index: [25] or less. Smoke-Developed Index: [50] [450] or less. LOW-PROFILE, FIXED-HEIGHT ACCESS FLOORING If retaining more than one panel type, indicate location of each on Drawings and insert drawing designation. Use these designations on Drawings to identify each product. Low-Profile, Fixed-Height Access Flooring: Manufacturer's [standard] [reinforced], modular, steel or polymer components, designed to interconnect and provide channels for installation of wiring; with manufacturer's standard factory-applied finish. Byrne Electrical; KIVA Flexible DIRTT Poweflor USA, Inc. Steelcase Inc. Retain "Module" Subparagraph below if desired to restrict module size. Verify available sizes with manufacturers. Module: Low-profile access flooring with nominal module size of [24 by 24 inches (610 by 610 mm)] [23.6 by 23.6 inches (600 by 600 mm)] . Retain "Height" Subparagraph below if desired to restrict height. Verify available heights with manufacturers. Height: Low-profile access flooring with nominal height of [1-1/2 inches (38 mm)] [2 inches (50 mm)] [3 inches (75 mm)] . Retain "Service Outlets and Wiring" Paragraph below if required. Designs of outlets differ among manufacturers; if retaining, revise to suit Project. Service Outlets and Wiring: Standard UL-listed and -labeled assemblies, for recessed mounting flush with top of floor panels; for power, communication, and signal services; and complying with the following requirements: Structural Performance: Cover capable of supporting a [300-lbf (1334-N)] [800-lbf (3559-N)] [1000-lbf (4448-N)] concentrated load. Cover and Box Type: [Hinged polycarbonate cover with opening for passage of cables when cover is closed and including frame and steel box or formed-steel plate for mounting electrical receptacles] [Grommet with twist-close cover and including steel junction box for electrical receptacle with provision for telephone connectors and signal cables] . Receptacles and Wiring: Equip each service outlet with power receptacles to comply with the following requirements: Type of Receptacle: Heavy-duty duplex, two-pole, three-wire grounding, 20燗, 125燰, NEMA燱D�6, Configuration�5-20R unless otherwise indicated. Number of Receptacles for Outlet: [One] [Two] [Four] . Retain one of two "Wiring Method" subparagraphs below. Wiring Method: Factory wired for field hardwiring with armored cable, containing three insulated No.�12燗WG solid-copper conductors, terminated with a [6-inch- (152-mm-)] long pigtail. Wiring Method: Power-in connectors, built into outlet housing, of type to fit power-in and power-out connectors of branch-circuit cables supplied with building electrical system. Fascia Closures: Where underfloor cavity is not enclosed by abutting walls or other construction, provide metal closure plates with [manufacturer's standard finish] . Retain "Ramps" Paragraph below if required for access from adjacent flooring. Indicate locations and details on Drawings. Ramps: Manufacturer's standard ramp construction of width and slope indicated, but not steeper than 1:12, of same materials, performance, and construction requirements as low-profile, fixed-height access flooring. If special extrusion or other means are required, indicate details on Drawings and revise "Perimeter Support" Paragraph below accordingly. Perimeter Support: Manufacturer's standard method for supporting panel edge and forming transition between low-profile, fixed-height access flooring and adjoining floor coverings at same level as low-profile, fixed-height access flooring. LOW-PROFILE, FIXED-HEIGHT ACCESS FLOORING WITH MODULAR WIRING If retaining more than one panel type, indicate location of each on Drawings and insert drawing designation. Use these designations on Drawings to identify each product. Manufacturers listed in this article include factory-assembled wiring harnesses as an integral part of their product. Low-Profile, Fixed-Height Access Flooring with Modular Wiring: Manufacturer's [standard] [reinforced], modular, steel or polymer components, designed to interconnect and provide channels for installation of wiring. Include factory-assembled modular wiring harnesses and service outlets; with manufacturer's standard factory-applied finish. Byrne Electrical; KIVA Flexible DIRTT Poweflor USA, Inc. Steelcase Inc. Retain "Height" Subparagraph below if desired to restrict height. Verify available heights with manufacturers. Height: Provide low-profile access flooring with nominal height of [1-1/2 inches (38 mm)] [2 inches (50 mm)] [3 inches (75 mm)] . Retain "Service Outlets and Wiring" Paragraph below if required. Designs of outlets differ among manufacturers; if retaining, revise to suit Project. Service Outlets and Wiring: Standard UL-listed and -labeled assemblies, for recessed mounting flush with top of floor panels; for power, communication, and signal services; and complying with the following requirements: Structural Performance: Cover capable of supporting a [300-lbf (1334-N)] [800-lbf (3559-N)] [1000-lbf (4448-N)] concentrated load. Cover and Box Type: [Hinged polycarbonate cover with opening for passage of cables when cover is closed and including frame and steel box or formed-steel plate for mounting electrical receptacles] [Grommet with twist-close cover and including steel junction box for electrical receptacle with provision for telephone connectors and signal cables] . Retain one of two "Receptacles and Wiring" subparagraphs below. Coordinate with electrical distribution system requirements and revise to suit Project. Receptacles and Wiring: Electrical receptacles and wiring for service outlets are specified elsewhere. Receptacles and Wiring: Equip each service outlet with power receptacles to comply with the following requirements: Type of Receptacle: Heavy-duty duplex, two-pole, three-wire grounding, 20燗, 125燰, NEMA燱D�6, Configuration�5-20R unless otherwise indicated. Number of Receptacles for Outlet: [One] [Two] [Four] . Wiring Method: Factory wired for field hardwiring with armored cable, containing three insulated No.�12燗WG solid-copper conductors, terminated with a [6-inch- (152-mm-)] long pigtail. Fascia Closures: Where underfloor cavity is not enclosed by abutting walls or other construction, provide metal closure plates with [manufacturer's standard finish] . Retain "Ramps" Paragraph below if required for access from adjacent flooring. Indicate locations and details on Drawings. Ramps: Manufacturer's standard ramp construction of width and slope indicated, but not steeper than 1:12, of same materials, performance, and construction requirements as low-profile, fixed-height access flooring. If special extrusion or other means are required, indicate details on Drawings and revise "Perimeter Support" Paragraph below accordingly. Perimeter Support: Provide manufacturer's standard method for supporting panel edge and forming transition between low-profile, fixed-height access flooring and adjoining floor coverings at same level as low-profile, fixed-height access flooring. FABRICATION Fabrication Tolerances: Size: Plus or minus 0.020 inch (0.50 mm) of required size. Flatness: Plus or minus 0.035 inch (0.89 mm), measured on a diagonal on top of panel. EXECUTION EXAMINATION Coordinate requirements specified in other Sections for subfloor construction and tolerances to ensure that they are appropriate for pedestal installation. Examine substrates, with Installer and manufacturer's authorized representative present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work. Verify that substrates comply with tolerances and other requirements specified in other Sections and that substrates are free of conditions and deleterious substances that might interfere with attachment of pedestals. Proceed with installation only after unsatisfactory conditions have been corrected. PREPARATION Fill cracks, holes, and depressions in substrates with trowelable leveling and patching compound; remove bumps and ridges to produce a uniform and smooth substrate. Lay out low-profile access flooring installation to keep the number of cut panels at floor perimeter to a minimum. Avoid using panels cut to less than 6 inches (152 mm). Complete any necessary subfloor preparation, and vacuum subfloor to remove dust, dirt, and construction debris before beginning installation. INSTALLATION Install low-profile, fixed-height access flooring and accessories under supervision of low-profile, fixed-height access-flooring manufacturer's authorized representative to produce a rigid, firm installation that complies with performance requirements and is free of instability, rocking, rattles, and squeaks. Install flooring securely in place and properly seated, with panel edges flush. Do not force panels into place. Scribe perimeter panels to provide a close fit with adjoining construction, having no voids greater than 1/8 inch (3 mm) where panels abut vertical surfaces. END OF SECTION 09 69 33 FOR MDACC USE ONLY. DELETE THIS PAGE BEFORE ISSUING DOCUMENTS. document revision history IssueDateRevision DescriptionAuthor20190301Original IssuanceRev. 1.Rev. 2Rev. 3 Rev. 4 Rev. 5 MD ANDERSON Project No. XXXXXXMD ANDERSON PROJECT NAMEA/E Name Issue Description A/E Project No.Month 00, 0000 麻豆映画 low profile fixed height access flooringMD Anderson Cancer Center09 69 33 mS 20190301 PAGE 8 of NUMPAGES 8 9B� ; n z } � = � � � � � 镙溯溯锕餂啗v泇泦沢R=)h?y�hx �0J/B*CJOJQJ^Jph�)h?y�hx �0J0B*CJOJQJ^Jph�h?y�hx �CJOJQJ^JhQ2�hx �5丆JOJQJ^J)h<hx �5�;�<丆JOJQJ^JaJhQ2�hx �CJOJQJ^Jh赿�0J.5丆JOJQJ^J#h?y�hx �0J.5丆JOJQJ^J#h?y�hQ2�0J-5丆JOJQJ^J#h?y�hx �0J-5丆JOJQJ^Jh?y�hx �5丆JOJQJ^J:BT��7 D � � ; � � � ��= � � � @��とgd<)�とgd<�とgd<�とgd<�とgd<�gd<� @�=�� 9�� '*9IKW��褴褴裉裉裉裉褴窦堙荞荞恬恬荞恲j恲j糺恲j糺h?y�hx �CJOJQJ^J,h?y�hx �0J/5丅*CJOJQJ^Jph�,h?y�hx �0J05丅*CJOJQJ^Jph�)h<h\t[5�;�<丆JOJQJ^JaJh?y�hx �5丆JOJQJ^JhQ2�hx �5丆JOJQJ^J)h<hx �5�;�<丆JOJQJ^JaJhQ2�hx �CJOJQJ^J)@�=�&�F"��9��1��とgd<�とgd<�とgd<�とgd<とgd<)�とgd<�� ^f��"$'*-9o��5px{�,-u�(7GJ]mp橐么ご暣ごごごごごご€搐搐磘h€撮颐橐�hNB�CJOJQJ^Jhx �CJOJQJ^J)h<hx �5�;�<丆JOJQJ^JaJhQ2�hp< CJOJQJ^JhQ2�hx �5丆JOJQJ^JhQ2�hx �CJOJQJ^Jh?y�hx �CJOJQJ^J,h?y�hx �0J/5丅*CJOJQJ^Jph�,h?y�hx �0J05丅*CJOJQJ^Jph�$� D�5-MSfu�� t!�"R#�#'$^$*%�%�&��とgd<�とgd<)�とgd<�とgd<とgd<p��./;CFNVYail|~ '!(!/!8!;!B!K!N!V!_!d!�!7":"�"�"�"$$ $ $$$$$$'$^$�$�$�$镟鸭燕啷庎囡嘌佳啷庎啷庎褈褈褈褈褈褈褈鸭燕�hQ2�hx �5丆JOJQJ^J,h?y�hx �0J/5丅*CJOJQJ^Jph�,h?y�hx �0J05丅*CJOJQJ^Jph�)h<hx �5�;�<丆JOJQJ^JaJhQ2�hx �CJOJQJ^Jh?y�hx �CJOJQJ^Jh?y�hx �5丆JOJQJ^J1�$% %%*%b&€&�&�&�& '�'n(�)�)�)�*'+/+2+<+,,L,R,t,�,&-'-3-;->-F-N-Q-Y-a-d-t-v-w- .橼授猾猾粬粬猾粬猾猾粖~姈悔g橼g橼g橼授粬,h?y�hx �0J05丅*CJOJQJ^Jph�hNB�CJOJQJ^Jh,�CJOJQJ^J)h<hx �5�;�<丆JOJQJ^JaJhQ2�hx �5丆JOJQJ^JhQ2�hx �CJOJQJ^Jh?y�hx �5丆JOJQJ^Jh?y�hx �CJOJQJ^J,h?y�hx �0J/5丅*CJOJQJ^Jph�(�& '�'n(])�)�*,,L,R,e,t,�,w- .�.l/�0n1�1I2�23�3�4��とgd<とgd<�とgd<�とgd<)�とgd< ./ /'/0/3/:/C/F/N/W/k/�//020�0�0�0�0n1�2�2333333�3�3�3�3�3�3�3o4�4�4�4�45�5{6�7�7疋舜馑粹舜怦ゑゑゑ忨ゑゑゑゑ馑粹怦ゑゑ忨忨�h?y�hx �5丆JOJQJ^J)h<hx �5�;�<丆JOJQJ^JaJhQ2�hx �5丆JOJQJ^J,h?y�hx �0J/5丅*CJOJQJ^Jph�,h?y�hx �0J05丅*CJOJQJ^Jph�h?y�hx �CJOJQJ^JhQ2�hx �CJOJQJ^J,�45�5{6r7~7�7�7'818=8�8�9�:�:�:�;0<��<��<�>r>?(?�� '$�a$gd*u�とgd<とgd<�とgd<�とgd<)�とgd<�7�7�7�7�7�7�7'818=8�8<�%<�.<�0<��>�>�>?!?"?$?%?'?(?)?h?暾脐掌阀窉逢掌逢辗俽俽俥]I'h祎�hM 5�;�<丆JOJQJ\乚�h祎�hM <�hM 5丆JOJQJ^JhQ2�hQ2�5丆JOJQJ^JhQ2�hx �5丆JOJQJ^J)h<hx �5�;�<丆JOJQJ^JaJh?y�hx �5丆JOJQJ^JhQ2�hx �CJOJQJ^Jh?y�hx �CJOJQJ^J)h?y�hx �0J/B*CJOJQJ^Jph�)h?y�hx �0J0B*CJOJQJ^Jph�(?h?�?�?�?�?�?�?�� $1$IfgdM 1$gdM $$とと$d&dN��P��a$gdM )�とgd1c�h?�?�?�?'@(@)@+@,@.@/@1@2@4@K@L@S@m@獲珸瑻瓳疈菮薂藹餈馌AAA钶陷壤祭祭祭吉敧仾}vrn猑N^仾^�h赿�;丆JOJQJ\乚乛JhQ2�;丆JOJQJ\乚乛JhQ2�hN}�hQ2�h1c�hx �%hQ2�hQ2�;丆JOJQJ\乚乛J+hQ2�hQ2�B*CJOJQJ\乚乛Jph�"hQ2�hQ2�CJOJQJ\乚乛JhGDjhGDUhQ2�hx �h赿�5丆JOJQJ\乚�!hM hM 5丆JOJQJ\乚�!hM hM ;丆JOJQJ\乚��?�?�?�?�?�?^SSSS $1$IfgdM �kd$$IfT杔�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣�?�?�?�?�?�?\QQQQ $1$IfgdM �kd�$$IfT杔�敎�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣�?�?�?�?�?�?^SSSS $1$IfgdM �kd8$$IfT杔�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣�?�?�?�?�?�?\QQQQ $1$IfgdM �kd�$$IfT杔�敎�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣�?�?�?�?�?�?^SSSS $1$IfgdM �kdp$$IfT杔�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣�?�?�?�?�?�?\QQQQ $1$IfgdM �kd $$IfT杔�敎�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣�?�?�?�?�?�?^SSSS $1$IfgdM �kd�$$IfT杔�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣�?�?�?�?�?�?\QQQQ $1$IfgdM �kdB$$IfT杔�敎�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣�?@@@@@^SSSS $1$IfgdM �kd�$$IfT杔�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣@@ @@@@\QQQQ $1$IfgdM �kdz$$IfT杔�敎�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣@@@@@@^SSSS $1$IfgdM �kd$$IfT杔�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣@@@@ @!@\QQQQ $1$IfgdM �kd�$$IfT杔�敎�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣!@"@#@$@%@&@^SSSS $1$IfgdM �kdP$$IfT杔�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣&@'@(@*@+@-@.@0@1@3@\TRRRRRRR &FgdM �kd�$$IfT杔�敎�謀��,$$��0览�览�览�览�览�览��$��4�4� la�yt�H奣 3@4@S@l@m@w@夽��x $$1$Ifa$gdQ2� $1$IfgdQ2�Nkd�$$IfT朒�0�x�$�`�6��4� Ha�yt�奣$ ��!$1$Ifa$gdQ2� $1$Ifgd赿�夽婡汙狜獲珸瑻瓳��JEEC2gdQ2�NkdR $$IfT朒�0�x�$�`�6��4� Ha�yt�奣 $$1$Ifa$gd赿� $1$IfgdQ2�Nkd�$$IfT朒�0�x�$�`�6��4� Ha�yt�奣瓳疈菮馌駺AA�� $$1$Ifa$gdQ2�Okd� $$If朒擴�0$��$��$��4� Ha�lytQ2� $$1$Ifa$gd赿� $1$IfgdQ2�AAAAA"A#A$A*A+A,A-A1A2AA?A@AAABACADA镘受很④s堍堍\s苁XTMhQ2�hx �hGDhN}�-h赿�;丆JOJQJ\乚乛JmHnHu�*1jhQ2�hQ2�;丆JOJQJU\乚乛J�**h赿�;丆JOJQJ\乚乛JmHnHu.jhQ2�hQ2�;丆JOJQJU\乚乛Jh1c�;丆JOJQJ\乚乛J"hQ2�hQ2�CJOJQJ\乚乛J%hQ2�hQ2�;丆JOJQJ\乚乛JhQ2�;丆JOJQJ\乚乛JAA#A@AAABACA��FDDOkd� $$If朒擴�0$��$�€&��$��4� Ha�lytQ2� $$1$Ifa$gdQ2� $1$Ifgd<Okd $$If朒擴�0$��$��$��4� Ha�lytQ2�CADA� &FgdM /<0BP靶/ 班=!盃"盃#悹$悹%�靶靶愋�$$If�!vh#v#v�#v�#v�:V杔�0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔敎��0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔�0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔敎��0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔�0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔敎��0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔�0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔敎��0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔�0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔敎��0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔�0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔敎��0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔�0览�览�览�览�览�览��$5�5��5��5��yt�H奣�$$If�!vh#v#v�#v�#v�:V杔敎��0览�览�览�览�览�览��$5�5��5��5��yt�H奣c$$If�!vh#v�#v`:V朒�6�5��5�`4�4� Hyt�奣c$$If�!vh#v�#v`:V朒�6�5��5�`4�4� Hyt�奣c$$If�!vh#v�#v`:V朒�6�5��5�`4�4� Hyt�奣e$$If杔!vh#v�#v�:V朒擴��$�5��5��4�4� Ha�lytQ2�e$$If杔!vh#v�#v�:V朒擴��$�5��5��4�4� Ha�lytQ2�q$$If杔!vh#v�#v�:V朒擴��$�,�5��5��9�4�4� Ha�lytQ2��<�s��666666666vvvvvvvvv666666>666666666666666666666666666�6666666666�666666666666hH66666666666666666666666666666666666666666666666666666666666666666�62��&6FVfv��2(��&6FVfv��&6FVfv��&6FVfv��&6FVfv��&6FVfv��&6FVfv��8X�V~��€�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@�� 0@_HmH nH sH tH <�`�<�NormalCJ_HmH sH tH DA`��D Default Paragraph FontRi@��R 0Table Normal�4� l4�a�(k ��( 0No List4��4HDR��$*$a$0�0FTR��$*$a$,﨩",SCTゐ*$a$6﨩R6PRT$Fむ*$@&a$6�b6SUT &Fゐ*$@&a$6�b6DST &Fゐ*$@&a$:﨩b:ART$ &Fむ*$@&a$6﨩b6PR1 &Fゐ*$@&a$2﨩r2PR2 &F*$@&a$2﨩�2PR3 &F*$@&a$2��2PR4 &F*$@&a$2��2PR5 &F*$@&a$0�b0TB1ゐ*$^� a$0�r0TB2ゐ*$^刞a$0��0TB3ゐ*$^劆a$0��0TB4ゐ*$^勦a$0��0TB5ゐ*$^� a$0��0TF1 ゐ*$^� a$0��0TF2!ゐ*$^刞a$0��0TF3"ゐ*$^劆a$0��0TF4#ゐ*$^勦a$0��0TF5$ゐ*$^� a$&�R&TCH%*$.�b.TCE &*$^剱`刾�,﨩r,EOS'む*$a$<��<�ANT(ゐ*$a$<�>*B*ph€€8﨩�870CMT)ゐ*$a$<丅*ph��CPR��SPN��SPD﨩��NUM﨩��NAM&䁖��&SI B* ph€€&䁖�&IP B*ph�*�*RJUST1a$4@"43W0Header 2�H�$.��1.2W0Header Char4 B45W0Footer 4�H�$.��Q.4W0Footer Char\�b\8� TIP26ゐN��O��P��Q�� B*ph�88�/�q8)� CMT Char<丅*CJph�4�/��46� TIP Char<€B*ph�8:�/��:l�SAhyperlink>*B*ph鉲 6U ��6l�0 Hyperlink>*B*ph�>�/��>� SustHyperlink>*B*ph�PK!檗�[Content_Types].xml瑧薔�0E鱄鼉�-J湶@%閭菐洽|廊�$韶钵UL襎B� l,�3鳛;鉹�得槣B+$�G]ミ7O侪V墎�c:菜�E3v@釶莮�憇� |煓w�<�<爔k猴ll5� 玈Z埣2O,辜帣Q績� €‰壪�5y�;y=卐E颎翼帊|\P疼鞭M7�$|n]�枌蓢]4忥`窾6涀G冼(垲�^斗菹颻琖��-翻関]m蓿瓄�  飍祡缧暺}攙旯缦r�鍧竔倲崜0�� D3劂梋閐�3譙钐嚟�耳杧:忲�8}d-楀鉯*壵x上轻qCよZ}�柣WlшqyI@赹剟6橧!Q_� ﹪s殔刏賩a汛癶H魉Tm�jyV`垆纅�榾惫�<箣犇鼁YpL8�*аx侏S&机;EUC�8⒊eE�<В悟hg贇!燴H睩x0� VM螽憆刳u�6拺覦s�3 U慮赢b��6�怂5y嵳2臓iz嘜]r汯璠�'鋆炃弦u涎4jj採�K臀F娃盶�晕�$4寨-莓�-�珠`餜�熘��&藑代觥瀈A<吼"xNW﹦� � 袬鞩R賭[鋺萵 8r� i箯K~�*~P(5黕莲z胦Wm忒杮~乖鞹濦caT鲇�.}x E僮5抉&Z緄�2bQ懇/,EE\}�)W�乹埼鉠ミ�6;礏弛�糿h礜贻~7�威�9R`痌糧疩〞儬嗾J拁▄旿郢�=$燮朗Sb酻紇��PK! 褠煻'theme/theme/_rels/themeManager.xml.rels剰M �0匃倃oo雍�&輬协�勪5 6?$Q祉 �,.嘺緳i粭澤c2�1h�:闀q毩m胳嶡RN壻;d癭値o7�g慘(M&$R(.1榬'J摐袏T鶂�8V�"＆A然蠬鱱}狇�|�$絙{�朠�除8塯/]As賲(⑵锑#洩L蔥汉倪��PK-!檗�[Content_Types].xmlPK-!ブх�60_rels/.relsPK-!ky��theme/theme/themeManager.xmlPK-!稝��theme/theme/theme1.xmlPK-! 褠煻'� theme/theme/_rels/themeManager.xml.relsPK]� D9�� p�$ .�7h?ADA!#%'(*,.@@��&�4(?�?�?�?�?�?�?�?�?�?@@@!@&@3@夽瓳ACADA"$&)+-/0123456789:;<�=>?AB� !t�晙t�晙餞� #�喠帕@��€€€�餒 ��0�( � �饞��0�( � �養 �S�� ?�S[R$Z$3"3(8*8+8-8.808183848B9E9��*�*(8*8+8-8.808183848B9E933 ::TT��<<DD,u,$t$!7"7$7%7'7'8(848�8�8#9-919?9A9E9DD,u,$t$'7'8(8N8N8�8�8�8�8�8�8�8�89999999"9#9-919?9A9A9E96x� PART - SCHEDULE - PRODUCT DATA SHEET - 刞劆��`^刞`劆�.刞劺��`^刞`劺�.劆劺��^劆`劺�.勦劺��^勦`劺�.� 劺�� ^� `劺�)刞劺��`^刞`劺�)�� MASTERSPEC��1�Xq_霮� p< iwM GDW<R&璵>�H�J凣PYZ\t[鈆\ =]mmi*uz賔zI|�~lC赿�x �NB�)M�%b�Q2�鱘�蘚�祎�H�1c���,� B�l��?y�俕�Q��nz�N}�(8*8��DOIFormatMF04MF95MFOriginSpecTypeVersion12/01/15109693310273MF04 MasterSpec11628�@€�7�7�7�7D9�@��Unknown��G��.郲x� �Times New Roman5�€Symbol3.��.郈x� �ArialA��$B�Cambria Math"1�愷h�h鎿t囨搕�a�/ea�/e�%愷€88J僸愷哌��HP � $P��W2!xx�€嫱P��9SECTION 096933 - LOW-PROFILE FIXED HEIGHT ACCESS FLOORING(LOW-PROFILE FIXED HEIGHT ACCESS FLOORINGBAS-12345-MS80Fitzgerald,Richard WFitzgerald,Richard W� 鄥燆鵒h珣+'迟0��(@P p| �� <�SECTION 096933 - LOW-PROFILE FIXED HEIGHT ACCESS FLOORING,LOW-PROFILE FIXED HEIGHT ACCESS FLOORINGFitzgerald,Richard WBAS-12345-MS80NormalFitzgerald,Richard W2Microsoft Office Word@@茰&鲈@茰&鲈a�/aboration/_layouts/15/DocIdRedir.aspx?ID=SZWXXFYDWACR-487-672, SZWXXFYDWACR-487-672AVITRU, LLC.e ?@ABC��EFGHIJK��MNOPQRSTUVWXYZ[\]^_`ab��defghij��mnopqr|��ux��yz��}~€Root Entry�� F`珝 (鲈w@Data ��D1Table��L�,WordDocument��1�SummaryInformation(��cDocumentSummaryInformation8��,�CompObj��rMsoDataStore��`:� (鲈`珝 (鲈�� !"#$%&'��)*+��-./0123456789:��<��>?@�� F Microsoft Word 97-2003 Document MSWordDocWord.Document.8�9瞦 DocumentLibraryF2N0�O�F��U�W��G0��5�==2�� `:� (鲈`:� (鲈Item �� lx.Properties��R��E��E��MP�R��KI�R�==2`:� (鲈`:� (鲈Item �� Properties�� LL�C�R��5LIQB4��==2��`:� (鲈`珝 (鲈Item ��eProperties��(��X�OH��4TGS�Y5��Q==2��`:� (鲈`珝 (鲈Item ��;€Properties��=��k��value="08"/> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. cumentation> This value indicates the number of saves or revisions. The application is responsible for updating this value after each revision. d:element name="contentStatus" minOccurs="0" maxOccurs="1" type="xsd:string"/> ormDocumentLibraryFormDocumentLibraryForm00Microsof Filter>Document ID GeneratorDocument ID GeneratorSynchronous100011000Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100021001Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100041002Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandlerDocument ID GeneratorSynchronous100061003Microsoft.Office.DocumentManagement, Version=14.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429cMicrosoft.Office.DocumentManagement.Internal.DocIdHandler � 胀諟.摋+,D胀諟.摋+,p,hp�� AVITRU, LLC.e8:SECTION 096933 - LOW-PROFILE FIXED HEIGHT ACCESS FLOORINGTitle88�€��H_dlc_DocId_dlc_DocIdItemGuid_dlc_DocIdUrl� SZWXXFYDWACR-487-672%d95484e5-0028-416f-aada-4a82758f46bethttp://fm/groups/cpm/TRG/odgColl